ericmoore68
New member
For your consideration is this essentially new ZERO mile 1992 TZ250. This machine is quite special and I will do my best to detail it below:
1992 TZ250D. Polished Frame. All new bearings (swing arm, steering head, wheel)
Suspension rebuilt will new oil, bushings, seals, set up for 185 lb rider.
.8 kg/mm fork springs 8.5 kg/mm shock spring
Rebuilt Shindy Daytona steering damper
ZERO mile Rick Schell crank shaft (crank is a work of art, lightened and polished fly wheels and rods)
ZERO mile top end (pistons, rings, bearings)
Roland Cushway 8.0cc heads
96' cylinders and pipes with 2.5mm pipe spacers per Roland Cushway
new plugs and caps
new reeds
new gaskets through out
dual EGTs
Daytona digital water temp gage
new clutch and pressure plate
every bearing in cases replaced with new (trans, case, waterpump, balance shaft)
new EBC HH brake pads
GP tech thumb brake
Custom rear sets and foot pegs
Vortex Clip-ons
new DID xring chain
EBC Prolite rotors
Professional paint
airtech aerotail w/anti draft sheild
Comes with a set of Bridgestone take-off slicks that have 1 race weekend on them. (9/24/16)
Gearing, jetting, original Yamaha paddock stand AND original manual included
Bike presents as new. I built it as my back up bike for this season, but I have no real need for another TZ250. Full set up notes included and a copy of my jetting spread sheet. The bike has been leak tested, started, heat cycled and ridden around the block so maybe not zero mile, but you get the point.
$10k takes it. Or trade for KTM 690 Enduro R or Husqvarna 701 Enduro
email ericmoore68@gmail.com or call/text 480-436-0192 serious inquiries only. I can ship anywhere in the continental US for $400-700 depending door to door. Located in Phoenix, AZ. Can deliver to Chuckwalla
Thanks for looking,
Eric
1992 TZ250D. Polished Frame. All new bearings (swing arm, steering head, wheel)
Suspension rebuilt will new oil, bushings, seals, set up for 185 lb rider.
.8 kg/mm fork springs 8.5 kg/mm shock spring
Rebuilt Shindy Daytona steering damper
ZERO mile Rick Schell crank shaft (crank is a work of art, lightened and polished fly wheels and rods)
ZERO mile top end (pistons, rings, bearings)
Roland Cushway 8.0cc heads
96' cylinders and pipes with 2.5mm pipe spacers per Roland Cushway
new plugs and caps
new reeds
new gaskets through out
dual EGTs
Daytona digital water temp gage
new clutch and pressure plate
every bearing in cases replaced with new (trans, case, waterpump, balance shaft)
new EBC HH brake pads
GP tech thumb brake
Custom rear sets and foot pegs
Vortex Clip-ons
new DID xring chain
EBC Prolite rotors
Professional paint
airtech aerotail w/anti draft sheild
Comes with a set of Bridgestone take-off slicks that have 1 race weekend on them. (9/24/16)
Gearing, jetting, original Yamaha paddock stand AND original manual included
Bike presents as new. I built it as my back up bike for this season, but I have no real need for another TZ250. Full set up notes included and a copy of my jetting spread sheet. The bike has been leak tested, started, heat cycled and ridden around the block so maybe not zero mile, but you get the point.
$10k takes it. Or trade for KTM 690 Enduro R or Husqvarna 701 Enduro
email ericmoore68@gmail.com or call/text 480-436-0192 serious inquiries only. I can ship anywhere in the continental US for $400-700 depending door to door. Located in Phoenix, AZ. Can deliver to Chuckwalla
Thanks for looking,
Eric
Attachments
-
IMG_1727.jpg107.7 KB · Views: 84
-
IMG_1753.jpg95.2 KB · Views: 92
-
IMG_1767.jpg70.5 KB · Views: 156
-
IMG_1769.jpg92.7 KB · Views: 67
-
IMG_1770.jpg100.3 KB · Views: 59
-
IMG_1771.jpg110.5 KB · Views: 68
-
IMG_1772.jpg106.5 KB · Views: 72
-
IMG_1773.jpg75.7 KB · Views: 56
-
IMG_1774.jpg88.7 KB · Views: 53