701 sm - Page 13 - BARF

stan23 · 08-20-2019, 10:46 AM

Quote:

Originally Posted by JesasaurusRex

I wanted to add, i def think you need the o2 dongle even when running the PCV. Ive run the bike with the pcv and the o2 sensor hooked up and with the dongle hooked up and the low end runs noticeably better with dongle. I know the pcv instructions say you don't need to run the dongle but i think the ecu fights the pcv when it gets the "real" o2 input.

Just thought it'd help someone out that was trying different maps. Might make you revisit some of the ones you didn't think were any good if you weren't using the dongle.

Interesting.

When I had my 2018 701, the fuel dongle did nothing for me. My fueling when in closed loop was pretty much spot on. No lean spots, no hesitation. I knew specifically the PCV was for the open WOT mapping in which helped a lot with the proper map.

I installed a PCV on my 2019 690 and this time Rottweiler also included the dongle for free so I installed it. Again, I didn't notice any difference in closed loop mode. My bike was pretty much spot on from the factory. But with Rottweiler's latest OTS map, the bike runs really_really good. I'm very happy!

/pic for attention.

JesasaurusRex · 08-21-2019, 11:22 AM

Quote:

Originally Posted by stan23

Interesting.

When I had my 2018 701, the fuel dongle did nothing for me. My fueling when in closed loop was pretty much spot on. No lean spots, no hesitation. I knew specifically the PCV was for the open WOT mapping in which helped a lot with the proper map.

I installed a PCV on my 2019 690 and this time Rottweiler also included the dongle for free so I installed it. Again, I didn't notice any difference in closed loop mode. My bike was pretty much spot on from the factory. But with Rottweiler's latest OTS map, the bike runs really_really good. I'm very happy!

/pic for attention.

Explained, very noticeable on my bike. Did you ever have the rott intake? I don't remember.

youtu.be/v4Er_H1DPLo

Bike looks killer btw

erok81 · 03-27-2020, 07:09 PM

I had to go a long way back to find this thread!

Here’s my latest mod. Brembo RCS master cylinder and abs delete.

awsnap · 03-28-2020, 10:56 AM

Thanks for reviving this thread. Gives me the excuse to add some pics. Here is my '20 701SM, lowered front and back by about 1.5". Now side stand is extra tall and I would not trust it parking bike on street. I am looking into a shorter side stand that may be available as part of a kit on listed accessories on website.

Compared to my WR20X it is super smooth and I am really digging it.

awsnap · 03-28-2020, 11:05 AM

Sorry about sideways pics I did not think they would come out that way

augustiron · 03-28-2020, 11:10 AM

A welder could shorten your stand for under $40

erok81 · 03-28-2020, 11:56 AM

Looks good! I like the new gray color. If you resized the pics (which you have to) they flip sideways sometimes.

For the stand, if you don’t have a welder do it, I think either slavens or rottweiler sells a shorter stand. Mine is stock height and I occasionally wish it was shorter. I can’t imagine being 1.5 lower and dealing with it.

1fastmexican · 04-05-2020, 11:15 PM

Whats up fellas? Just wanted to introduce myself to all you SM riders. My name is Oscar Fernandez AKA 1 Fast Mexican and I'm California's Michelin road race dealer. If you guys ever want to buy Michelin SM tires shoot me a PM or give me a call at my shop Race Pace MotorSports. I have 17 and 16.5 SM tires in stock. Also if you call please mention barf as I like to donate back to this forum for their support. Thanks and stay safe during these crazy times.

JesasaurusRex · 04-06-2020, 08:04 AM

Quote:

Originally Posted by erok81

I had to go a long way back to find this thread!

Here’s my latest mod. Brembo RCS master cylinder and abs delete.

And how do you like it?

Quote:

Originally Posted by awsnap

Thanks for reviving this thread. Gives me the excuse to add some pics. Here is my '20 701SM, lowered front and back by about 1.5". Now side stand is extra tall and I would not trust it parking bike on street. I am looking into a shorter side stand that may be available as part of a kit on listed accessories on website.

Compared to my WR20X it is super smooth and I am really digging it.

That grey actually looks way better than i thought it would. Looks great man!

erok81 · 04-08-2020, 09:29 PM

Quote:

Originally Posted by JesasaurusRex

And how do you like it?

That grey actually looks way better than i thought it would. Looks great man!

No clue. Haven’t ridden yet. I reeeeaally want to. I’m curious about the brake. Sitting in the garage it feels 10x better than the stock one.

banshee01 · 04-09-2020, 06:04 PM

Quote:

Originally Posted by erok81

I had to go a long way back to find this thread!

Here’s my latest mod. Brembo RCS master cylinder and abs delete.

Looks nice, let's see your whole bike

banshee01 · 04-09-2020, 06:19 PM

Quote:

Originally Posted by jokerio

I have a 2017 (the manual chain adjuster is the same for the 16-17, even though the motor changed to a two-counter balanced motor) The 2018 and up had a revised (auto) cam chain adjuster, the adjuster is at an angle now, and thread pitch is different.

So if you are in the market for a manual cam chain adjuster, make sure to order the correct one.....

I was looking at OEM parts diagram and the cam chain tensioner has the same part number for 16,17 and 18

#77036003000

Also aftermarket listings is see are 17'-20'

I have been looking because my 701SM valvetrain is loud. Deffinilty making more noise than my 701 Enduro. Good time to look into it now

erok81 · 04-25-2020, 07:29 PM

Quote:

Originally Posted by banshee01

Looks nice, let's see your whole bike

Just finished up a bunch of mods; one being new graphics.

banshee01 · 04-26-2020, 04:10 PM

Quote:

Originally Posted by erok81

Just finished up a bunch of mods; one being new graphics.

Very nice

bunnygoat · 05-25-2020, 01:04 PM

What kind of mileage are you guys getting before its rebuild time?

03-27-2020, 07:09 PM	#183
erok81 Rookie Join Date: Feb 2018 Location: Santa Cruz Motorcycles: Husky 701 Name:	I had to go a long way back to find this thread! Here’s my latest mod. Brembo RCS master cylinder and abs delete. Attached Thumbnails Last edited by erok81; 03-27-2020 at 07:11 PM..

03-28-2020, 10:56 AM	#184
awsnap Newbie Join Date: Jul 2018 Location: West Sacramento Motorcycles: 2009 WR250X; 2020 701 SM Name: Jeremy	Thanks for reviving this thread. Gives me the excuse to add some pics. Here is my '20 701SM, lowered front and back by about 1.5". Now side stand is extra tall and I would not trust it parking bike on street. I am looking into a shorter side stand that may be available as part of a kit on listed accessories on website. Compared to my WR20X it is super smooth and I am really digging it. Attached Thumbnails

04-05-2020, 11:15 PM	#188
1fastmexican Ride Fast Take Chances 8% Contributor Join Date: Sep 2009 Location: San Jose Motorcycles: Race only 2014 R6, 2016 R1m Name: Oscar	Whats up fellas? Just wanted to introduce myself to all you SM riders. My name is Oscar Fernandez AKA 1 Fast Mexican and I'm California's Michelin road race dealer. If you guys ever want to buy Michelin SM tires shoot me a PM or give me a call at my shop Race Pace MotorSports. I have 17 and 16.5 SM tires in stock. Also if you call please mention barf as I like to donate back to this forum for their support. Thanks and stay safe during these crazy times. __________________ Race Pace MotorSports (408) 9eight2-31one1 Michelin Road Race & SM Distributor for California NEED A TOW CALL Race Pace MotorSports

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-28-2020, 11:05 AM	#185
awsnap Newbie Join Date: Jul 2018 Location: West Sacramento Motorcycles: 2009 WR250X; 2020 701 SM Name: Jeremy	Sorry about sideways pics I did not think they would come out that way

03-28-2020, 11:10 AM	#186
augustiron 2fast 2live 2young 2die Join Date: Mar 2003 Location: Truckee SF Reno Motorcycles: All of them eventually. Name: nope	A welder could shorten your stand for under $40

03-28-2020, 11:56 AM	#187
erok81 Rookie Join Date: Feb 2018 Location: Santa Cruz Motorcycles: Husky 701 Name:	Looks good! I like the new gray color. If you resized the pics (which you have to) they flip sideways sometimes. For the stand, if you don’t have a welder do it, I think either slavens or rottweiler sells a shorter stand. Mine is stock height and I occasionally wish it was shorter. I can’t imagine being 1.5 lower and dealing with it.

05-25-2020, 01:04 PM	#195
bunnygoat Veteran Contributor Join Date: Feb 2004 Location: Oakland Motorcycles: 950SM Name: Dan	What kind of mileage are you guys getting before its rebuild time?