BARF - Bay Area Riders Forum

Go Back   BARF - Bay Area Riders Forum > Classifieds > Moto for Sale

Thread Tools Display Modes
Old 01-23-2018, 01:49 PM   #1

Join Date: Nov 2012
Location: Santa Rosa
Motorcycles: 2006 ZX6R 636 (track) & 2005 ZX6R 636 (street)
Name: Joey T
2006 Zx6r 636 Track Bike

2006 Kawasaki ZX6R. 17,812 OD.

Ohlins GP forks rebuilt and respringed for 205# rider by race tech. Elka rear shock rebuilt and respringed (eibach spring) for 205# rider. Racing front brake rotors. ebc pads front and rear. yosh "full exhaust". all diy mods done, block off plates etc. dunlop gpa with no tread left. did chain 520 sprocket. frame and wheels powder coated gloss black. Kawi race ecu (not power commander) and KIT harness installed and tuned by EDR (oregon). Tuned on the rich side (for 110) cus i was trying to cool the engine down a little but in doing so, flames out the back. I call that a downside because you'll need EDR to retune. not that it runs bad, just that people seem to complain about the flames out the back. engine case covers (vortex and NRC) right and left sides. vortex rear sets. driven clip ons (crap IMO) and driven block off plates (also crap that needed to be machined for fitment). steel braided lines (lines are a little too big and prob should be trimmed down). top tripple anodized black. original seat with lui moto cover. a lot of little details but there's a build thread for that.

4500 or best offer. Comes with pitbull rear stand and cheap front stand, and new vortex tire warmers and a heavily used easy up. Moving out of state, need moving monies or else I wouldn't sell. I spent the better part of 2 years pulling this apart and methodically putting it back together while making sure a shop does the major stuff so if I had to sell people wouldn't think it's mickey moused. Mammoth for valves and then put back to rolling chasis and edr for the tune. I tried using best parts I could find.

I'd service forks soon. Replace the tires obviously. and if possible lean it out a little. EDR will pick up the bike at the track. Race ecu kills fan so it's on a ghetto rigged switch, I have a clip on mounted switch in storage so I know they exist. I would suggest getting one and replacing the ghetto with something more official. The only thing not safety wired is the lowers on the forks. but due to it's complexity, you may have to get that done somewhere or remove the forks to DIY.

Bike was used a lot after (the better) photos were taken so expect that before coming to see. Never crashed. Never been down. Never raced LOL but plenty of track time before and after these photos were taken.
Attached Thumbnails
Click image for larger version

Name:	ImageUploadedByTapatalk1414790908.538546.jpg
Views:	46
Size:	168.2 KB
ID:	504399   Click image for larger version

Name:	ImageUploadedByTapatalk1414790947.955340.jpg
Views:	33
Size:	247.8 KB
ID:	504400   Click image for larger version

Name:	IMG-0749.jpg
Views:	26
Size:	83.0 KB
ID:	504402   Click image for larger version

Name:	IMG-0750.jpg
Views:	11
Size:	26.7 KB
ID:	504403   Click image for larger version

Name:	IMG-0751.jpg
Views:	11
Size:	56.7 KB
ID:	504404  

Click image for larger version

Name:	IMG-0753.jpg
Views:	8
Size:	64.2 KB
ID:	504405   Click image for larger version

Name:	IMG-0754.jpg
Views:	8
Size:	71.1 KB
ID:	504406  

Last edited by MasterTurkey; 01-23-2018 at 03:16 PM.. Reason: contact info
MasterTurkey is offline   Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -8. The time now is 12:22 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.